Epilog Fusion M2 Laser Series

The Fusion M2 32 and the larger Fusion M2 40!

It's our new concept in laser system design, featuring:

  • 32" x 20" (812 x 508 mm) or 40" x 28" (1016 x 711 mm) engraving area
  • Our new standard for motion control design
  • Better flame-polished edge cuts
  • Our highest engraving and cutting speeds
  • Large viewing door with LED lighting
  • Dual source (fiber and CO2) and camera options available.

And we're proud to say it is designed, engineered and built in the USA!


Epilog Fusion Laser Series Models

Two models to choose from to meet your needs.

Epilog Fusion M2 32 Laser: With a large table size of 32" x 20" (812 x 508 mm), the Fusion M2 32 is our newest product offering! The high quality engraving across the entire table is a result of the highest-quality components, high-speed servo motors, and the exciting optional Dual Source and Camera Registration options.

Epilog Fusion M2 40 Laser: With an oversized table of 40" x 28" (1016 x 711 mm), the Fusion M2 40 features Epilog's largest work area. This machine was designed to engrave the same high-quality image at any point on the table by utilizing our top-of-the-line motion control system and industry-leading optics system.

Epilog Fusion Series Technical Specifications

Epilog Fusion M2 32 Epilog Fusion M2 40
Engraving Area 32" x 20"
(812 x 508 mm)
40" x 28"
(1016 x 711 mm)
Maximum Material Thickness CO2: 13.5" (343 mm) (2" lens)
Fiber: 12.5" (318 mm) (3" lens)
Dual Source: 12.5" (318 mm) (3" lens)
CO2: 13.25" (337 mm) (2" lens)
Fiber: 12.25" (311 mm) (3" lens)
Dual Source: 12.25" (311 mm) (3" lens)
Laser Wattage CO2: 30, 40, 50, 60, 75, or 120 watts
Fiber: 30 or 50 watts

Dual source: CO2 50, 60, or 75 watts;
Fiber 30 or 50 watts
CO2: 30, 40, 50, 60, 75, or 120 watts
Fiber: 30 or 50 watts

Dual source: CO2 50, 60, or 75 watts;
Fiber 30 or 50 watts
Laser Source State-of-the-art, digitally controlled, air-cooled CO2 laser tubes are fully modular, permanently aligned and field replaceable.
Intelligent Memory Capacity Multiple file storage up to 128 MB.
Air Assist Attach an air compressor to our included Air Assist to remove heat and combustible gases from the cutting surface by directing a constant stream of compressed air across the cutting surface.
Laser Dashboard The Laser Dashboard™ controls your Epilog Laser's settings from a wide range of software packages - from design programs to spreadsheet applications to CAD drawing packages.
Red Dot Pointer Since the laser beam is invisible, the Red Dot Pointer on the Fusion Laser allows you to have a visual reference for locating where the laser will fire.
Relocatable Home When engraving items that are not easily placed at the top corner of the laser, you can set a new home position by hand with the convenient Movable Home Position feature on the Fusion Series Lasers.
Operating Modes Optimized raster, vector or combined modes.
Motion Control System High-speed Brushless DC Servo Motors.
X-Axis Bearings Ground and polished stainless steel Long-Lasting Bearing System.
Belts Kevlar (x-axis) and Steel Cord (y-axis) belts.
Resolution User controlled from 75 to 1200 dpi.
Speed and Power Control Computer or manually control speed and power in 1% increments to 100%. Vector color mapping links speed, power and focus to any RGB color.
Print Interface 10 Base-T Ethernet or USB Connection. Compatible with Windows® XP/Vista/7/8/10.
Size (W x D x H) 52.5" x 33.75" x 40.75"
(1334 x 857 x 1035 mm)
37.75" (959 mm) deep with exhaust plenum.
60.5" x 41.25" x 42.25"
(1537 x 1048 x 1073 mm)
43" (1092 mm) deep with exhaust plenum.
Weight 500 lbs (227 kg)
Dual Source: 536 lbs (243 kg)
643 lbs (292 kg)
Dual Source: 679 lbs (308 kg)
Electrical Requirements Auto-switching power supply accommodates 110 to 240 volts, 50 or 60 Hz, single phase.
Maximum Table Weight Fusion 32/40: 200 lbs (90 kg) for static and 100 lbs (46 kg) for lifting.
Ventilation System 650 CFM (1104 m3/hr) external exhaust to the outside or internal filtration system is required. There are two output ports, 4" (102 mm) in diameter. 650 CFM (1104 m3/hr) external exhaust to the outside or internal filtration system is required. There are two output ports, 4" (102 mm) in diameter.

Fusion Laser Series Videos

Watch videos about the creative laser applications available to owners of an Epilog Fusion laser system, and the wide range of materials the Epilog Fusion laser can engrave and mark.

Fusion M2 40

epilog fusion m2 40 video

The Fusion M2 40 with a 40"x28" engraving area.

Watch Now

Fusion M2 Dual Source

epilog fusion m2 dual source

Mark a variety of materials with the Fusion M2 Dual Source.

Watch Now

Epilog eView Software

epilog eview camera video

Camera registration for laser die cutting.

Watch Now

FiberMark Fusion Demo

FiberMark 24 and FiberMark Fusion Metal Mark Demonstration Video

Watch as Bob Henry shows how to use the FiberMark and FiberMark Fusion.

Watch Now

iPad Air Laser Engraving

ipad air engraving

Watch as we laser engrave an iPad Air with our new Mac driver for the Fusion Laser.

Watch Now

Mac Driver Introduction

Introducing the Mac Driver Video

Watch as we introduce the world's first Mac driver for a laser system!

Watch Now

Mac Driver Demonstration

How to Use the Mac Driver with Ben Sieber Video

See how you can setup a file using our new Mac driver for the Fusion Laser.

Watch Now
Engrave Cut
Wood x x
Acrylic x x
Fabric x x
Glass x
Coated Metals x
Ceramic x
Delrin x x
Cloth x x
Leather x x
Marble x
Matte Board x x
Melamine x x
Paper x x
Mylar x x
Pressboard x x
Rubber x x
Wood Veneer x x
Fiberglass x x
Painted Metals x
Tile x
Plastic x x
Cork x x
Corian x x
Anodized Aluminum x
Stainless Steel *
Brass *
Titanium *
Bare Metals *
* CO2 lasers will mark bare metals when coated with a metal marking solution. For more information, visit our laser metal marking page.
Do you have a material you would like us to test? Our Applications Team would be happy to assist you.

We're proud to say that all Epilog laser systems are 100% designed, engineered and manufactured in the USA at our headquarters in Golden, CO.

Yes! Personalization and customization of products is in high demand. Adding a laser engraving service to your current operation is an excellent way to reach possible new customers as well as offer a valued service to your current client base. If you have any doubts about the profitability of owning a CO2 laser system, visit our Applications page or read our many Customer Success Stories.

For some insight into the profitability of laser engraved products, take a look at the website for LaserBits, a supplier of laserable materials. There you will find purchase prices for raw laserable materials and suggested retail prices for those same products once they have been laser engraved.

Also check out our new Guidebook to Starting Your Own Engraving & Cutting Business to see the ins and outs of starting a new laser business.

You can engrave scanned photos, logos, bitmaps, other images, text, and AutoCAD files. Essentially, if you can print it, you can engrave it.

To cut, you will need a vector based graphic, such as an .eps or Illustrator file.

Keep in mind the higher the quality of the graphic you're working with, the better your engraving results.

Yes. Our fiber laser systems are capable of permanently marking nearly all types of bare metal. The fiber laser line was designed with a combination of affordability and high quality results in mind. The Fusion M2 series features a 32" x 20" (812 x 508 mm) or 40" x 28" (1016 x 711 mm) work area. The flat-bed, flying-optic design of the Fusion M2 is revolutionary for a fiber laser system and will mark metals over a large work area in a short amount of time.

And, though our CO2 laser systems are mainly designed to engrave and cut non-metallic materials, they can also be used to mark on metal with the aid of metal-marking compound. Download our PDF to learn more about marking metal with a CO2 laser system.

Since we use low power CO2 (30 to 120 watts) and fiber lasers (10 to 50 watts) the beam will clearly mark on coated and raw metal but our systems are not ideally suited for metal-cutting applications. Our fiber laser systems may be compatible for cutting some thin metals as we have seen success cutting thin foils, up to .012", with our fiber lasers.

Please contact our Applications Lab to discuss your metal-cutting applications and see if they can work with our systems!

Yes, the laser is completely safe to operate. It is a Class 2 laser - 1 mW CW MAXIMUM 600-700 nm, which means that the laser is secured with interlock devices so it will not run with the doors of the system open. No special safety gear is required to run the laser.

The cost of operating the laser can be easily figured out by plugging your electricity rates into the following formula using even our highest wattage laser, the 120 watt.

Typical Max power consumption = 1560 Watts (This assumes full power, constant laser on.) If power costs $0.075/KWH in your area, it is costing $0.117/hour to operate the laser. Or, about 12 cents per hour, or 96 cents per eight hour day. (1560 x .075)/1000 = .117

No, one laser does it all! Our CO2 laser systems will engrave and cut most non-metallic materials, as well as engrave coated metals. For information on what materials you can engrave and cut, visit our Materials page.

The laser can be set to engrave only (Raster Mode), cut only (Vector Mode), or can complete both operations in Combined Mode. The laser knows what portions to engrave and what portions to cut based on line width, which is easily set in your graphic design software.

Investing in a new computer is a great way to make sure you’re getting the most out of your new laser equipment. Why? Because today’s software requires a lot of computer processing speed and memory to function properly. A good computer won’t make a huge difference in how your laser runs, but when compared to a slow computer it will save untold amounts of time and frustration setting up the artwork that you “print” to the laser. Many users do not purchase new computers for use with their new laser because their current computers are perfectly adequate. There’s no magical cut-off that makes a computer too slow. If you’re comfortable with the performance and speed of your current computer, there’s probably no reason to purchase another one. The following recommendations are just options to consider if a new computer is necessary.

A new computer doesn’t have to be expensive to work well! Even many of today’s lower-cost computers work well for laser applications. As long as you don’t buy the cheapest computer you can find you should be fine. One thing to avoid is the Intel Celeron processor – while they are good processors, and will work with the laser, they don’t process graphics with the speed most laser users desire.

  • Operating System: All new Epilog lasers are designed to work with all versions of Windows 2000, XP, Vista, 7, 8, or 10 operating systems.

    The Fusion Laser Series is also compatible with Mac operating systems OS X 10.7 and higher. Read more about our Fusion Mac Driver here.
  • RAM (Random Access Memory): 512 MB is recommended. RAM is kind of like short-term memory. It’s fast, readily available for the computer to access and makes time consuming tasks go much quicker if you have lots of it. Most users won’t notice a difference if they add more than 512 MB to their system, but almost all uses will notice the speed difference that 512 MB provides when compared to 256 MB (256 MB is essentially the next step down from 512 MB).
  • Processor Speed: A faster processor will allow you to do more tasks in less time. While it’s not necessary to purchase the fastest processor available, you’ll want either an AMD Athalon processor or an Intel Pentium IV processor (do not purchase a computer that is using an Intel Celeron processor – they’re too slow for graphics applications). Processor speeds are always improving, but processor speeds of about 2.0 GHz or faster are a good place to start.
  • 10/100 Network Interface Card (NIC): All new computers have a 10/100 network connection as standard equipment. As well as allowing multiple computers to be linked together in a network, this technology also allows direct printing from the computer to the Epilog system. Epilog supplies a network Crossover cable with each laser system that allows one computer to print to a single Epilog system.
  • 20-30 GB Hard Drive: This is the permanent memory in your computer. Many users feel that you can never have a large enough hard drive, but for most laser applications 20 or 30 GB’s is going to be adequate for years of storage. Luckily, most computer manufacturers put at least 20 GB drives in new computers these days. When in doubt, buy bigger than you think you might need. It’s so inexpensive that it’s worth the peace of mind to have it available.

Rim-Drive Rotary Attachment: 10.25" (260 mm) outside

3-Jaw Chuck Rotary Attachment: 6.5" (165 mm) outside, 3.125" (79 mm) inside

+/- .01" (0.254 mm) over the entire table
0.003" - 0.005" (0.0762 - 0.127 mm)

Fusion 32/40: 200 lbs (90 kg) for static and 100 lbs (46 kg) for lifting.

Email us or give us a call at +1 303 277 1188. We're happy to supply all of the answers you're looking for.

Fiber Laser FAQs

The source is a fiber laser: a fiber optic cable that has been doped with ytterbium, a rare earth element.

The fiber laser produces the same wavelength of light and the same marks. YAG lasers typically require cooling and more maintenance.

Yes, especially to the operator's eyes. Additionally the wavelength will pass through common Lexan or glass materials, which is why the viewing window has been impregnated with an organic compound that absorbs the fiber energy. Do not run the laser with the safety locks defeated.

The fiber laser pulls 8-10 amps on a 110-volt circuit, and 4-5 amps on a 220 volt circuit.

All metals can be engraved into with some depth; however, some metals are more amenable to depth engraving. Softer aluminum material will engrave with depth with only a few passes. The best way to test your material is with our Applications Lab.

The Fiber Laser can only cut through very thin gauge metals. We've had success at cutting up to 0.012" (.30 mm) thick metals.

Yes, by using the polished mark settings for bare metal, the black oxide color will be removed to expose the lighter native metal color.

Systems start below $35,000 (US price only) for a 30 watt system.

Let's find out! Fill out our request form to receive a brochure and samples. Or contact our Applications Lab to get started testing your materials.

Receive a Brochure and Samples


Get More Information

laser engraver brochure